Cabot's EasyDeck™ Maintenance Coat
Zoom
Quickly and easily refresh the look of your timber with the Cabot's EasyDeck™ clean and coat maintenance system and be back on your deck in 40 minutes.*
Simply shake a bottle of EasyDeck™ Maintenance Coat, firmly load into the EasyDeck™ Applicator (sold separately). Once pushed into place, twist the bottle to ensure it is completely docked and you're ready to coat. No prep is required because the EasyDeck™ Applicator Pad is specially designed to remove dirt and dust from timber whilst ensuring even coating.
EasyDeck™ is designed for application over existing water-based coatings that are in good condition.
Cabot's EasyDeck™ is the fast, no mess deck refresher.
*Conditions of 25°C and 50% relative humidity. More humid or cooler conditions will need longer drying times.
| Areas |
|
|---|---|
| Sizes |
|
| Suitable surfaces |
Exterior coated timber^ must be at least 4 weeks after the last recoat |
| Return to use |
40 mins* |
| Coverage |
16 m2/L |
Safety Data Sheet
Get ready for use
Slide on the EasyDeck™ Applicator Pad and close the latch firmly. Insert the pole and twist the collar until the pole is securely attached.
How to quickly & easily refresh the look of your timber decking
Shake & insert
Shake the EasyDeck™ bottle for 1 minute prior to using. Shake only with the bottle cap on and keep it handy for later use. Replace the bottle cap with the dispensing nozzle and screw on firmly. Place the EasyDeck™ bottle into the applicator firmly.
Get coating!
Unhook the trigger and squeeze the handle 6-10 times until the applicator pad is soaked. Use long, smooth strokes along the direction of the boards. Avoid excessive coating. Wait 40 minutes for the coating to dry, and it's ready to walk on!
Clean up
Remove the applicator bottle from the applicator vertically without tilting. Replace the dispensing nozzle with the bottle cap. Unused EasyDeck™ coating can be stored in a cool, dry area for up to a year. Rinse the dispensing nozzle and the applicator pad under running water until the water runs clear. Flush the applicator body with running water whilst pumping the yellow cleaning levers on the sides until the water runs completely clear.
Storage & repeat use Store in a cool, covered area. It is recommended to wait at least 40 days between uses. The Cabot's EasyDeck™ maintenance system is recommended for use between normal recoat cycles of Cabot's Aquadeck®. Allow at least 30 days after reapplying Aquadeck® to use the EasyDeck™ maintenance system.
The applicator bottle should be removed from the applicator and stored with the original cap (not dispensing nozzle) in an upright position in a cool place. If stored properly, the shelf life of the coating will not be compromised (i.e. 5+ years from date of manufacture).
Take your Cabot's EasyDeck™ Maintenance Coat bottle and shake for 1 minute with the bottle cap attached. If the bottle is empty, shake the refill bottle, sold separately, for 1 minute and pour the liquid into the applicator bottle. Replace the bottle cap with the dispensing nozzle cap and screw on tightly.
Place the bottle inside the applicator and press down firmly. Once pushed into place, twist the bottle to ensure it is completely docked. Now squeeze the applicator handle 5 to 6 times and lift the applicator up to confirm liquid is dripping through the pad onto the deck. Now you're ready to coat!
Cabot's EasyDeck™ 1.5L Maintenance Coat
Shake, load, and you're ready to coat
Get back on your deck in 40 minutes*
Cabot's EasyDeck™ 1.5L Maintenance Coat
Calculate total usage
If you are unsure how much product you need, please use our product calculator. Please note minimum length/width is 1 metre and maximum is 50 metres.