Cabot's Garden Furniture Oil

Lasting longer than traditional outdoor furniture oils, Cabot’s Garden Furniture Oil is a highly durable way to enhance the natural grain of timber furniture. With advanced UV protection and water, dirt and mould resistance, it brings a semi-transparent finish to outdoor timber furniture.

Areas
  • Exterior timber
  • Garden furniture
  • BBQ trolleys
  • Benches
Sizes
  • 500mL
  • 1L
  • 2L
Application
Item Icon
Brush
Item Icon

Spray

Touch Dry
1 hour
Re-coat
2 hours
Coverage

12 m2/L

Cleaning
Item Icon
Water

Icon for Hot tip! tip

Hot tip!

Fill holes and imperfections with a suitable timber putty.

To coat new bare timber immediately, scrub damp timber with Cabot’s New Timber Prep, following label instructions.

New Timber Prep will draw out tannins and oils quickly from the surface, allowing you to skip the 4-6 weeks weathering process required for new timber.

Remove back to bare timber using a paint stripper, or sanding.

For exterior surfaces clean with Cabot’s Deck Clean following label instructions.

For exterior surfaces clean with Cabot’s Deck Clean following label instructions, then allow timber to fully dry. Test if the surface is ready for coating by sprinkling water on the timber. If the water beads on the surface, repeat the application of Cabot’s Deck Clean. If water is absorbed into timber, it is ready for coating. For a more transparent look, sand timber back to bare before coating.

For best results, sand timber back to fresh substrate. Clean with Cabot’s Deck Clean following label instructions.

Icon for Hot tip! tip

Hot tip!

Do not apply this product in temperatures below 10°C or above 35°C, or when rain or heavy dew is expected during the drying period. In hot temperatures do not apply in direct sunlight, cool the timber by lightly dampening with water and coat in the shade.

Application:

  1. Stir thoroughly with a broad flat paddle before and during use.
  2. Using a brush, apply liberally along the length of the timber including exposed edges and end grain. 
  3. Apply two coats allowing 2 hours between coats.
Icon for Hot tip! tip

Hot tip!

The initial milky colour helps with even product application, drying to a semi-transparent finish.

Every 12 months check your coated timber for changes in colour or water repellency diminishes due to weathering. When required.

  1. Clean the surfaces with Deck Clean as per label instructions.
  2. Recoat with 2 coats of Garden Furniture Oil.
Icon for Hot tip! tip

Hot tip!

Use Cabot’s Clean & Care Exterior Wipes to refresh exterior timber furniture and help remove dirt, dust and bird droppings.

Cabot's Garden Furniture Oil

ups icon UV protection
ups icon Dirt and mould resistant
ups icon Fast recoat
ups icon Water repellent
selected-color-swatch
Select colour range
arrow-right
Select Colour
Semi-transparent, natural look that enhances the timber grain with matt finish. To view our range, view the colour visualiser.
Merbau

Colour - Merbau

Timber type - Meranti

New Natural

Colour - New Natural

Timber type - Meranti

Jarrah

Colour - Jarrah

Timber type - Meranti

Before image After image
2
COATS
All colours displayed on this page show 3 coats on meranti timber.
Colour Accuracy: Due to image limitations, colours are a general guide only and do not represent the actual colour. Please test your colour selection at home on a timber cutoff of the same timber you will be coating before coating your timber.
Cabot's Garden Furniture Oil
Stock levels and product variants may vary across retailer websites due to ongoing inventory changes. Please review the retailer’s product page carefully before completing your purchase.
Calculate total usage

If you are unsure how much product you need, please use our product calculator. Please note minimum length/width is 1 metre and maximum is 50 metres.

Coats*
The number of coats is a general guide only. Actual product requirements may vary based on surface type, condition and preparation.
Your approx need
Your measurements
Amount needed
This usage calculator provides a general guide only. Actual product requirements may vary based on surface type, condition and preparation, and application method.